Training Water Flooding Basic Theory and Operation

OBJECTIVES :

After participate in thid Training Water Flooding Basic Theory and Operation, the participants will be abble and cappable to :

  • Understand the basic concept of waterflooding processes and how to operate this technology in field application.
  • Diagnostic of reservoir performance under actual drive mecanism and future performance under waterflooding processes.
  • Analyze the production potential of reservoir under waterflooding processes and to plan the field development.
  • Understand the fundamentals of microscopic and macroscopic aspects and phenomena of reservoir under waterflooding processes.

PRE-REQUISITE:

Basic Petroleum Engineering or field experience

AUDIENCE:

No specified  (Operator/Sr. Operator/Engineer or Non Engineer)

COURSE OUT-LINE:

Introduction to  Waterflooding

Microscopic Efficiency of Immicsible Displacement

  • Fluid and Rock Interaction
  • Methods of Inferring Fluid Distribution in Porous Media
  • Multiphaseflow in Porous Media
  • Residual Saturation
  • Mobilization of Residual Oil

Macroscopic Displacement Efficiency of a Linear Waterflood

  • Development of Equations
  • Frontal Advanced for Unsteady Displacement
  • Linear Waterflood
  • Numerical Model

Waterflood Displacement in Two Dimensions-Areal

  • Development of Equations
  • Fivespot Pattern
  • Scaled Laboratory Models
  • Prediction of Areal Displacement

Vertical Displacement in Linear and Areal Models

  • Layered Models
  • Gravity Segregation and Crossplot in Linear Reservoir
  • 2D Flow With Thichness-Averaged Properties
  • Scaled Laboratory Models

Waterflooding Design

DURATION

3 Day

FASILITY

Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket, etc, Convenient training facilities in four or five stars hotel

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Water Flooding Basic Theory and Operation 2025:

  • 06-08 Januari 2025 Jakarta
  • 03-05 Februari 2025 Yogyakarta
  • 03-05 Maret 2025 Bandung
  • 02-04 April 2025 Surabaya
  • 05-07 Mei 2025 Bogor
  • 02-04 Juni 2025 Bali
  • 01-03 Juli 2025 Jakarta
  • 04-06 Agustus 2025 Yogyakarta
  • 01-03 September 2025 Bandung
  • 01-03 Oktober 2025 Surabaya
  • 03-05 November 2025 Bogor
  • 01-03 Desember 2025 Malang

INVESTASI (TIDAK TERMASUK BIAYA AKOMODASI & PENGINAPAN) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Wireline Technology

PENGANTAR

Training Wireline Technology– Technology Wireline sektor perindustrian oil and gas merupakan media instrument yang digunakan untuk mengirimkan atau mengoperasikan special downhole equipment di dalam sumur migas. Dimana ada 2 macam wireline dalam industri migas bisa yaitu: Pertama: Slickline, yaitu wireline yang digunakan terutama untuk mengoperasikan wireline equipment dalam pekerjaan2 workover/well intervention, completion, fishing job, gas lift installation dan sejenisnya dalam sumur migas. Dalam hal ini biasanya wireline equipment tsb berfungsi berdasarkan prinsip mekanis dan dioperasikan dengan manipulasi ‘tarik’ dan ulur’ oleh operator wireline di permukaan. Kedua: Electric wireline disingkat E-Line, yaitu wireline yg digunakan dalam pekerjaan-pekerjaan formation evaluation, logging untuk temperature survey, production survey, kualitas semen di belakang casing, perforasi, memotong tubing atau casing dalam sumur migas. Umumnya e-line berfungsi berdasarkan prinsip elektonik dan komputerisasi, ada pula yang dengan sinyal2 gelombang suara. Sesuai namanya, tentu e-line beroperasi dengan signal signal  listrik oleh operatornya di permukaan. Bagi anda yang ingin mengetahui Technology Wireline lebih dalam sangat direkomendasikan untuk mengikuti Training Wireline Technology dimana akan dibahas secara detail di mulai dari prinsip dasar orientasi teknologi tersebut di plant oil and gas serta membuat estimasi perhitungan dan simulasi dengan akurasi data seactual mungkin dengan kondisi aslinya dilapangan

Training Wireline Technology  bertujuan agar peserta memahami dan mampu:

  • Memahami konsep dasar dari wireline technology
  • Memahami cara untuk mengoperasikan wireline technology
  • Menggunakan instrumentasi wireline technology dalam aplikasi industri oil and gas dan melakukan perawatan untuk menjaga kondisi peralatan agar tetap siap beroperasi.
  • Mampu mendiagnosa minyak dan gas dan performa reservoir dan mekanisme actual dengan wireline technology
  • Mampu menganalisa potensi sumur minyak dengan menggunakan  wireline technology
  • Memahami dasar dan fenomena wireline technology dalam industri oil dan gas, perbaikan operasi, permasalahan produksi dalam industri oil and gas.

PESERTA YANG DIREKOMENDASIKAN

Operator produksi industri oil dan gas, engineer, departemen utilitas, departemen maintenance dan semua pihak yang terlibat dalam pengolahan industri minyak dan gas.

Wireline Survey

  •  Solving Well Mechanical Problems
  •   Supporting Drilling amd Workover Activity
  • Well Data Acquisitions

The Well

  • General Background
  •  Casing Diagram, Well Head, Xmast Tree
  •  Basic Tree types, Sample Completion Schematic
  • Tubing, Tubing Threads

Wireline Surface Equipments

  • General Safety
  • Atuffing Box, Quick Unions, Lubricator
  • BOP, Tree Connection, Weight Indicators

Wireline Units

  •  Spooling Wireline, Wireline Handling
  • Tensile Testing, Torsion Testing, Wire Breaks
  • Braided Line, Wireline Unit
  •  Open Loop Unit, Close Loop Unit

Tool String Components

  •  Rope Sockets, Wireline Knox,
  • Swivel, Stem, Roller Stem
  •  Mechanical Jars, Hydraulic Jars, Petroline Spring Jars
  • Petroline Centraliser, Knuckle joint,  Sucker Rod Threads

Standard Service Tools

  • Gauge Cutter, Blind Box, Imprssion Block
  • Swaging Tool, Wire Scratcher
  • Tubing End Locator
  • SSJ Tools, Pulling Tool  Data, Fishing Neck, GS Tools

Lock Mandrels

  • Lock Mandrels, W Sleep Lock, W running Tool
  • D Collar Lock, D Runing Tools, G Elements
  • Nipple Lock, X/XN Lock, X Running Tools
  • Petroline Uniset Lock Size Reference Chart

Plugs

  • Plug/Equalising Subs
  • D Plug, XX Plug, P/PS Plug, PX Plug
  • Test Tools, Test Tool, Back Pressure Valves
  • Cameron BPV
  • Petroline ABC BPV

Circulating Device

  • XO SSD
  • B Shifting Tool
  • Selective Downshift Tool
  • Separation Tool
  • Side Door Choke

Well Safety System

  • DCSSV
  • DK SCSSV
  • Camco WRDV Safety Valve
  • Troubleshooting Guide
  • SSV, Control Panel

Gas Lift

  • Gas  Lift Principle
  • Side Pocket Mandrel
  • Gas Lift Equipments
  • Kick Over Tool
  • Special Valve Types

BHP Ameradas

  • BHP Survey
  • Amerada Gauges
  • Calibration, Running Procedures
  • Data Recording

Remedial Wireline

  •  A Perforator
  •  F Collar Stop
  •  Sand Bailing
  •  Pump Bailer
  •  Pack Offs

Fishing

  •  Fishing Wire
  •  Wire Finder, Wire Grab
  •  Tubular Jar, Accelerator, Allegator Grab
  • Wire Cutter, Citter Bar, Side Wall Cutter, Go-Devil
  •  Heavy Duty Pulling Tool, Overshot, Center Spears

Calculation-Conversion

  • Basic Formula
  • Rule of Tumbs
  • Force, Hydrostatic Pressure

DURASI

3 Hari

FASILITAS

Normal Class

  • Sertifikat, Modul (Soft dan Hard Copy) Flash disc, Training kit (Ballpoint Tas jinjing), Tas Ransel, Jacket, Lunch, 2x Coffe break, foto bersama dan pelatihan dilaksanakan di Hotel berbintang.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Wireline Technology 2025:

  • 07-09 Januari 2025 Jakarta
  • 21-23 Januari 2025 Bogor
  • 04-06 Februari 2025 Yogyakarta
  • 18-20 Februari 2025 Surabaya
  • 04-06 Maret 2025 Bandung
  • 18-20 Maret 2025 Jakarta
  • 02-04 April 2025 Surabaya
  • 15-17 April 2025 Yogyakarta
  • 06-08 Mei 2025 Bogor
  • 20-22 Mei 2025 Jakarta
  • 03-05 Juni 2025 Jakarta
  • 17-19 Juni 2025 Bali
  • 02-04 Juli 2025 Bogor
  • 15-17 Juli 2025 Yogyakarta
  • 05-07 Agustus 2025 Surabaya
  • 19-21 Agustus 2025 Jakarta
  • 02-04 September 2025 Bandung
  • 16-18 September 2025 Bogor
  • 01-03 Oktober 2025 Surabaya
  • 14-16 Oktober 2025 Yogyakarta
  • 04-06 November 2025 Bogor
  • 18-20 November 2025 Jakarta
  • 02-04 Desember 2025 Yogyakarta
  • 16-18 Desember 2025 Surabaya

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

REFERENSI

  1. Kangean Energy Indonesia Ltd.
  2. Chevron Geothermal Indonesia, Ltd

TESTIMONIAL

  • “Untuk materi yang diberikan oleh Trainer sangat menambah wawasan kami dan memberi gambaran bagaimana wireline technology tersebut” Fakih Setiawan, Operator produksi – Kangean Energy Indonesia Ltd.
  • “Secara keseluruhan untuk training Wireline Technology yang di selenggarakan oleh BMD Street Cosnsulting berjalan dengan sangat baik” Dawud Efendi. Operator produksi – Kangean Energy Indonesia Ltd.

METODE OFFLINE

 

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

 

Training Reservoir Fluid Analysis

INTRODUCTION

Hydrocarbon systems found in petroleum reservoirs are known to display multi-phase behavior over wide ranges of pressure and temperatures. The most important phases which is occur in petroleum reservoirs are: liquid phase (crude oil or condensates) and gas phase (natural gases).  This course will explain the fundamentals of hydrocarbon phase behavior and practical application in reservoir and production engineering. Firstly it will reviews the principles of phase behavior and ilustrate the use of phase diagram in describing the volumetric behavior of single-component, two-component, and multi-component system.

Also it will present numerous mathematical and graphical correlation for estimating physical and critical properties of the undefined petroleum fraction, evaluation of properties of natural gases and introduces their application in Darcy’s equation and material balance equation.  A complete and cohesive independent unit on methods of determining the crude oil physical properties , presents the concept and application of  vapor-liquid phase equilibria, developments and advanced in the field of empirical cubic equation of state and application in petroleum engineering. Details sceheme of splitting and lumping of petroleum-fraction.

Properly understanding the reservoir fluid properties is very significant and are very importance steps  during the entire life of the oil and reservoir developments and operations. This five-day training will provide a comprehensive knowledge and understanding of reservoir fluid properties and application to reservoir and production engineering to keep exellent reservoir and production performance as long as possible.

OBJECTIVES

  • Refresh the knowledge of the participants on reservoir fluid properties.
  • Understand the basic principles of hydrocarbon phase behavior and it’s application in petroleum engineering.
  • Learn the numerous mathematical and graphical correlation for estimating physical and critical properties of the undefined petroleum fraction
  • Enhance the knowledge on hydrocarbon phase behavior , freservoir fluid properties and application.
  • Gain additional knowledge on reasent technology in reservoir fluid properties calculation and correlation.
  • Knowledge sharing among the participants and instructors

FEATURING THE FOLLOWING SUBEJCTS :

Basic Phase Behavior

  • Single Component  Systems
  • Two Component  Systems
  • Multy Component  Systems
  • Classification of Reservoir and Reservoir Fluids

Pure Component Physical Properties and Characterizing Undefined Petroleum Fraction

  • General Correlation for Estimating Physical Properties of Hydrocarbon Fraction
  • Critical Compressibility Factors
  • Characterizing Hydrocarbon Heavy Fractions
  • Determining of Physical Properties of Heavy Petroleum Fraction from Correlation

Properties of Natural Gases

  • Behavior of Ideal Gases
  • Ideal Gas Mixtures
  • Properties of Ideal Gas Mixtures
  • Behavior of Real Gases
  • Effect of Non Hydrocarbon Components on the Z-Factor
  • Correction for Non Hydrocarbons
  • Correction for High-Molecular-Weight Gases
  • Direct Calculation of Compressibilty Factors
  • Compressibility of Natural Gases
  • Gas Formation Volume Factor
  • Gas Viscosity
  • Engineering Application of natural gases PVT Properties

Phase Behavior of Crude Oils

  • Crude Oil Density and Specific Gravity
  • Methods for Determining Density of Crude Oils as Unknown Composition
  • Methods for Determining Density of Liquids as Unknown Composition
  • Isothermal Compressibility Coefficient of Undersaturated Crude Oils
  • Density of Undersarurated Crude Oils
  • Gas Solubility
  • Oil Formation Factor of Undersaturated Crude Oils
  • Total Formation Volume Factor
  • Total System Isothermal Compressibility Coefficient
  • Crude Oil Viscosity
  • Bubble Point and Surface Tension
  • Application of the Crude Oil PVT P
  • The Material Balance Equation for Oil Reservoirs

Vapor-Liquid Phase Equilibria

  • Equilibrium Ratio
  • Flash Calculation
  • Application of Equilibrium Ratio in Petroleum Engineering

Equation of State

  • The General ized Form of Equation of State
  • Application of Equation of State for Petroleum Engineering
  • Three-Phase Equilibrium Calculation

Splitting Lumping Schemes of Petroleum Fraction

  • Splitting Schemes
  • Lumping Schemes
  • Simulation of Laboratory PVT Data by Equation of State

DURATION

3 Day

FASILITY

Normal Class

  • Sertifikat, Modul (Soft dan Hard Copy) Flash disc, Training kit (Ballpoint Tas jinjing), Tas Ransel, Jacket, Lunch, 2x Coffe break, foto bersama dan pelatihan dilaksanakan di Hotel berbintang.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Schedule Training Reservoir Fluid Analysis Year 2025:

  • 20-22 Januari 2025 Jakarta
  • 24-26 Februari 2025 Bogor
  • 24-26 Maret 2025 Yogyakarta
  • 21-23 April 2025 Medan
  • 26-28 Mei 2025 Bali
  • 23-25 Juni 2025 Surabaya
  • 21-23 Juli 2025 Bogor
  • 25-27 Agustus 2025 Bali
  • 22-24 September 2025 Jakarta
  • 20-22 Oktober 2025 Yogyakarta
  • 24-26 November 2025 Bandung
  • 22-24 Desember 2025 Bali

Investation (Not Include Hotel Acomodation) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Available on request for time, place and facilities call us for more information

Training Nodal Analysis and Production Optimization

TARGET DAN TUJUAN :

Setelah menyelesaikan training  ini diharapkan peserta dapat :

  • Memahami prinsip-prinsip dasar perhitungan optimisasi produksi sumur-sumur minyak, gas dan reservoir panas bumi, pengembangan pelaksannaan optimisasi produksi ini untuk meningkatkan kinerja produksi sumuran dan lapangan.
  • Melakukan diagnosis sederhana dan memengerti penyelesaian optimisasi produksi dengan analisis nodal.
  • Membuat analisis sederhana terhadap data sumuran minyak, gas dan panas bumi , melakukan peramalan kinerja dan merencanakan pengembanganya.
  • Melakukan perhitungan-perhitungan kuantitatip sederhana dari seluruh data perolehan data tubing, flowline, choke, perforasi, gravel-pack, sub-surface savety valve pada sumuran, merencanakan pengembangannya dengan memperhitungan kemampuan masing-masing sumuran.
  • Mempergunakan pengetahuan optimisasi untuk aplikasi dalam cara pengkatan buatan dengan gas-lift, submersible-pump, sucker rod pump dan hidraulic pump.

PESERTA YANG DIREKOMENDASIKAN :

Latar belakang  : Operator/Senior Operator/Engineer/Non Engineer

MATERI TRAINING :

Production System Analysis

  • Nodal System Analysis Model
  • Nodal System Analysis  Application

Reservoir Performance

  • Equations and Inflow Performance Relationship
  • Real-Time Performance of Oil Wells
  • Performnace Prediction of Oil Wells
  • Real-Time Performance of Gas Wells
  • Performnace Prediction of Gas Wells
  • Effect of Water Production

Pressure Drop of Fluid Flow in Pipes

  • General Equations and Concepts
  • Fluid Properties : Density,Compressibility Factor etc.
  • Well-Flow Correlations
  • Pipeline Flow Correlations
  • Chokes and Valves Pressure Drop
  • Effect of Velocity

Total System Analysis

  • Tubing Design
  • Flowline Size
  • Effect of Stimulation
  • Chokes and Valves
  • Effect of Completion

Artificial Lift Method

  • Gas Lift
  • Submersible Pump
  • Succker Rod Pump
  • Hydraulic Pump

Nodal Analysis in Specific Field Application

  • Pressure Drop Calculation in Steam Line
  • Pressure Calculation in Injection Wells
  • Pressure Calculation in Production Wells
  • Total Analysis Approach

DURASI

3 Hari

FASILITAS

Normal Class

  • Sertifikat, Modul (Soft dan Hard Copy) Flash disc, Training kit (Ballpoint Tas jinjing), Tas Ransel, Jacket, Lunch, 2x Coffe break, foto bersama dan pelatihan dilaksanakan di Hotel berbintang.

Normal Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Nodal Analysis and Production Optimization tahun 2025:

  • 20-22 Januari 2025 Jakarta
  • 24-26 Februari 2025 Bogor
  • 24-26 Maret 2025 Yogyakarta
  • 21-23 April 2025 Medan
  • 26-28 Mei 2025 Bali
  • 23-25 Juni 2025 Surabaya
  • 21-23 Juli 2025 Bogor
  • 25-27 Agustus 2025 Bali
  • 22-24 September 2025 Jakarta
  • 20-22 Oktober 2025 Yogyakarta
  • 24-26 November 2025 Bandung
  • 22-24 Desember 2025 Bali

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Stuck Pipe

LATAR BELAKANG :

  • Merupakan salah satu masalah lubang sumur di operasi pemboran
  • Menyebabkan timbulnya biaya ekstra yang cukup besar
  • Berpotensi menyebabkan hilangnya sebagian drillstring di dalam lubang sumur
  • Menunda waktu produksi sumur (pop)

SASARAN :

  • Mengetahui jam kejadian pipa terjepit.
  • Mengetahui kerugian akibat penundaan POP.
  • Mengetahui usaha pencegahan terjadinya pipa terjepit.
  • Mengetahui cara mengidentifikasi mekanisme pipa terjepit yang terjadi.
  • Mengetahui kronologi terjadinya pipa terjepit.

PESERTA YANG DIREKOMENDASIKAN :

Latar belakang  : Operator/ Sr. Operator/ Jr. Engineer/Non Engineer

MATERI TRAINING  :

TEORI DASAR STUCK PIPE

Pengertian stuck pipe
Mekanisme/jenis-jenis stuck pipe

  • Hole pack off
  • Bridge
  • Differential stuck pipe
  • Wellbore geometry

PENGERTIAN STUCK PIPE

  • Ada Gaya yang Menahan
  • Drillstring Tidak Bisa Ditarik
  • Operasi Pemboran Terhenti

TIGHT HOLE:

  • Ada Gaya yang Menahan
  • Drillstring Agak Sulit Ditarik
  • Operasi Pemboran Tetap jalan
  • Berpotensi menyebabkan Pipa Terjepit

HOLE PACK OFF

  • Pembersihan Lubang yang Tidak Bagus
  • Mengendapnya Partikel Solid (Cutting, Caving, LCM) Di Annulus
  • Tidak Bisa Sirkulasi Lumpur

Terdiri Dari:

  •  Cutting yang Mengendap
  •  Shale yang Tidak Stabil
  •  Formasi yang Tidak Terkonsolidasi
  •  Formasi yang Banyak Mengandung Rekahan
  •  Faktor Semen

CUTTING YANG MENGENDAP

Faktor-faktor yang mempengaruhi pembersihan lubang yaitu:

  • Kecepatan pemboran / Rate of Penetration (ROP)
  • Kestabilan lubang
  • Kecepatan anular
  • Rheologi lumpur
  • Waktu sirkulasi
  • Besarnya sudut / kemiringan sumur

BRIDGE

  • Sirkulasi masih bisa dilakukan
  • Hampir sama dengan Hole Pack Off
  • Contoh: Junk, blok semen, dll

DIFFERENTIAL STUCK PIPE

  • Sebab
  • Syarat
  • Ciri2

WELLBORE GEOMETRY

  • Stiff Assembly
  • Keyseat
  • Micro Dogleg
  • Ledges
  • Mobile Formation
  • Undergauge Hole

KEYSEAT

  • Terjadi akibat dogleg yang terlalu besar
  • Tensi pipa yang tinggi + putaran pipa menggerus ke formasi
  • Dari atas penampangnya terlihat seperti lubang kunci
  • BHA dengan OD lebih besar tersangkut

SHALE YANG TIDAK STABIL

  • Shale yang reaktif
  • Geo-pressured shale
  • Hydro-pressured shale
  • Overburden shale
  • Tectonic stress

UNCONSOLIDATED FORMATION

  • Filter cake tidak ada atau tipis
  • Derajat sementasi antar butir rendah
  • Tekanan hidrostatis tidak mampu menahannya

FRACTURED FORMATION

  • Terjadi pada NFR (limestone)
  • Pecahan formasi jatuh dan menyumbat annulus drillstring

MOBILE FORMATION

  • Formasi mudah bergerak /bersifat plastis (garam, shale)
  • Tekanan overburden menekan formasi
  • BHA terjepit di formasi yang mengecil

STIFF ASSEMBLY

  • Adanya dogleg di dalam lubang sumur
  • OD BHA (stabilizer, dll) mengecil

UNDERGAUGE HOLE

  • Pemboran pada batuan keras dan abrasif
  • Diameter bit mengecil
  • Bit baru dengan diameter lebih besar terjepit

FAKTOR SEMEN

  • Semen belum mengering dengan sempurna
  • Tekanan pompa mempercepat semen mengeras
  • Semen yang tidak stabil di sekitar kaki casing/di area squeeze plug

DURASI

3 Hari

FASILITAS

Normal Class

  • Sertifikat, Modul (Soft dan Hard Copy) Flash disc, Training kit (Ballpoint Tas jinjing), Tas Ransel, Jacket, Lunch, 2x Coffe break, foto bersama dan pelatihan dilaksanakan di Hotel berbintang.

Normal Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Stuck Pipe tahun 2025:

  • 22-24 Januari 2025 Bogor
  • 19-21 Februari 2025 Surabaya
  • 19-21 Maret 2025 Bandung
  • 15-17 April 2025 Yogyakarta
  • 21-23 Mei 2025 di Medan
  • 18-20 Juni 2025 Jakarta
  • 16-18 Juli 2025 Bali
  • 20-22 Agustus 2025 Yogyakarta
  • 17-19 September 2025 Bogor
  • 15-17 Oktober 2025 Surabaya
  • 19-21 November 2025 Bandung
  • 17-19 Desember 2025 Yogyakarta

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Pump and Turbine Selection,Design and Operation for Oil and Gas Production Facilities

OBJECTIVES :

After participate in this training, the participants will be able and capable to :

  • Understand the basic concept of oil and gas handling with surface processes and operation facilities , and how to operate pump and turbine technology in field application.
  • Diagnostic of oil and gas flow  performance under actual pumping drive mechanism and future performance with current handling processes.
  • Analyze the production flow potential of oil and gas flow under actual handling facilities system processes and to plan the better development processes according to fluid flow capacity.
  • Understand the fundamentals of microscopic and macroscopic aspects the phenomena of oil and gas handling processes and operation with given surface facilities and pumping using turbine system.

AUDIENCE:

No specified  (Operator/ Sr. Operator/Engineer or Non Engineer)

COURSE OUT-LINE:

Introduction to Oil and Gas Production Operation

Oil Surface Production Facilities

  • Well Equipments
  • Pigging System
  • Separator
  • Gas Scrubber
  • Gas Dehydarator
  • Pumps : Centrifugal, Reciprocating, Diaphragm

Gas Surface Processing Facilities

  • Gas Sweetening
  • Heat Exchanger
  • Fractination, Liquification, Refrigeration System
  • Compressor

Pump Basic Theory

  • Centrifugal Pump
  • Conservation of Mass
  • Specific Velocity
  • Pump Performance
  • Cavitation

Pump Specification

  • Pump Specification
  • Flow Capacity
  • Fluid Properties
  • Head
  • Net Positive Heads
  • Rotation Determination and Pump Types
  • Viscous Fluid Correction
  • Material Selection
  • Prime Movers Selection

Pump Application

  • Pump Instalation Plan
  • Pump Application Example

Pump Construction

  • Pump Classification by Impeller
  • Pump Classification by Casing
  • Pump Classification by Stage Number
  • Pump Classification by Axis Position

Pump Operation

  • Head Capasity Curve
  • Parallel and Serrial Operation
  • Capasity Regulator
  • Water Hummer
  • Surging
  • Pressure Fluctuation
  • Automatic Operation

Pump Instalation

  • Horizontal Instalation
  • Vertical Instalation
  • Submersible Instalation
  • Pipping System
  • Vibration and Noise Protection

Pump Maintenance

  • First Inspection
  • Operation Condition Obervation
  • Savety Instrument
  • Maintenace Management
  • Overhaul

Pump Trouble Shooting

  • General Trouble Shooting
  • Submersible Pump Trouuble Shooting

Turbine Fundamental Concept

  • Gas turbine thermodynamics
  • Machinery components analysis : Compressor, Combustor, Gas producer turbine and Power turbine, sealing system
  • Gas turbine performance
  • Off design behavior
  • Gas turbine material
  • Gas turbine control (speedtronic) and instrument

Gas Turbine operation and maintenance

  • Gas turbine predictive maintenance and preventive maintenance
  • (Vibration, lube oil analysis) and interval maintenance
  • Gas turbine failure and failure analysis (case study)
  • Life cycle cost (Cost effectives) of gas turbine
  • Selection and Application gas turbine of gas transmission and pumping

DURATION

3 Day

FASILITY

Normal Class

Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket or T-shirt, etc, Convenient training facilities in four or five stars hotel, Lunch per day, morning and afternoon coffee / tea breaks for along the training, Certificate & Photo.

Online Class

Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Schedule Training Pump and Turbine Selection,Design and Operation for Oil and Gas Production Facilities year 2025:

  • 06-08 Januari 2025 Jakarta
  • 03-05 Februari 2025 Yogyakarta
  • 03-05 Maret 2025 Bandung
  • 02-04 April 2025 Surabaya
  • 05-07 Mei 2025 Bogor
  • 02-04 Juni 2025 Bali
  • 01-03 Juli 2025 Jakarta
  • 04-06 Agustus 2025 Yogyakarta
  • 01-03 September 2025 Bandung
  • 01-03 Oktober 2025 Surabaya
  • 03-05 November 2025 Bogor
  • 01-03 Desember 2025 Malang

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Principles and Practice of Flow Measurements

OBJECTIVE

Training Principles and Practice of Flow Measurements – This course is intended to give a breadth and depth analysis in oil and gas flow measurement problems which are actually and frequently occurred in the field. In this course the way to diagnose and solve the problem will be shown. Beside that how to detect ant determine micelleneous constituents inoil and gas will be presented too. The participants will be brought to current methods in analyzing oil and gas flow measurement problems that occured in actual fields. Skills in identifying various problems will be build during the course. The modern technique uses a relatively complicated method, but, more accurate and serves much more information needed for oil and gas floe measurement.

After participate in this training, the participants will be able and capable to

  • Understand the basic concept of oil and gas flow measurement , oil and gas handling processes and operation, and how to operate this technology in field application.
  • Analyze the oil and gas flow measurement  under with actual handling system processes using various methods and to plan the better development of oil and gas processing system.
  • Understand the fundamentals of microscopic and macroscopic aspects and phenomena of oil and gas flow measurement, oil and gas  detection, calculation and operation.

COURSE CONTENS

Introduction to Standard Oil and Gas Measurement Tools.

  • Level
  • Density
  • Temperature

Notion of Static and Dynamic Measurement

  • ASTM Table in Oil Volume Calculation

Land Tank Measurement

  • Calibration Table
  • Oil sampling technique
  • Level, Density and Temperature Measurement.

Land Tank Volume Calculation

  • Liter 150C-Barrel 60oF
  • Oil Stock Calculation
  •  Bill of Loading Calculation
  • After Reciept Calculation
  • Supplay Calculation
  • Working and Discharge Calculation

Oil Losses

  • Kind of losses
  • Cause and sources of losses
  • Losses Calculation
  • Methodology to reduce losses

Flow Measurement and Technology

  • Principle of Oil Flow Measurement
  • Direct Measurement
  • Turbin
  • Elektromagnetic
  • Vortex
  • Ultrasonik
  • Coriolis
  • Thermal Mass
  • Positif Displacement
  • Variabel Area (rotameters)

Indirect Measurement

  • Orifice
  • Flow Nozle
  • Venturi
  • Wedge
  • V-cone
  • Pitot tube / Anubar
  • Target meter

Multiphase Flow Meter

  • MPFM Phylosophy
  • Multiphase Flow
  • MPFM Technology
  • MPFM Design Guidelines

DURATION

3 Day

FASILITY

Normal Class

  • Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket, etc, Convenient training facilities in four or five stars hotel.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Schedule Training Principles and practice of Flow Measurements year 2025:

  • 06-08 Januari 2025 Surabaya
  • 20-22 Januari 2025 Bogor
  • 03-05 Februari 2025 Yogyakarta
  • 17-19 Februari 2025 Jakarta
  • 03-05 Maret 2025 Malang
  • 17-19 Maret 2025 Bandung
  • 02-04 April 2025 Surabaya
  • 14-16 April 2025 Bogor
  • 05-07 Mei 2025 Malang
  • 19-21 Mei 2025 Jakarta
  • 02-04 Juni 2025 Yogyakarta
  • 16-18 Juni 2025 Bandung
  • 01-03 Juli 2025 Surabaya
  • 14-16 Juli 2025 Bogor
  • 04-06 Agustus 2025 Bali
  • 18-20 Agustus 2025 Yogyakarta
  • 01-03 September 2025 Jakarta
  • 15-17 September 2025 Yogyakarta
  • 01-03 Oktober 2025 Bandung
  • 13-14 Oktober 2025 Surabaya
  • 03-05 November 2025 Bogor
  • 17-19 November 2025 Malang
  • 01-03 Desember 2025 Jakarta
  • 15-17 Desember 2025 Yogyakarta

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

REFERENSI

  1. Chevron Geothermal Salak
  2. Chevron Geothermal Indonesia, Ltd.
  3. PT. Chevron Pacivic Indonesia
  4. Chevron SMO

TESTIMONIAL

  • “Materi training sangat berguna untuk pekerjaan saya dan pemateri sangat menguasai materi. over all training ini sangat baik dan berkesan” Imam Baihaqi Salam-Chevron Geothermal Indonesia, Ltd.

Principle-BMD

Training Production Operation and Problem Solving

LATAR BELAKANG :

Setelah menyelesaikan Training Production Operation and Problem Solving ini diharapkan peserta dapat :

  • Memahami prinsip-prinsip dasar perhitungan dan melakukan optimisasi pada saat operasi produksi sumur-sumur minyak, gas dan reservoir panas bumi dilaksanakan, pengembangan pelaksannaan optimisasi produksi ini untuk meningkatkan kinerja produksi sumuran dan lapangan.
  • Melakukan diagnosis sederhana dan memengerti penyelesaian permasalahan dalam operasi produksi sumur-sumur minyak dan bas bumil.
  • Membuat analisis sederhana terhadap data sumuran minyak, gas dan panas bumi ,melakukan peramalan kinerja dan merencanakan pengembangn operasi produksi
  • Melakukan perhitungan-perhitungan kuantitatip sederhana dari seluruh data perolehan data tubing, flowline, choke, perforasi, gravel-pack, sub-surface savety valve pada sumuran, merencanakan pengembangannya dengan memperhitungan kemampuan masing-masing sumuran.
  • Mempergunakan pengetahuan operasi produksi untuk keperluan penyelesaian permasalahan sumur seperti : pada saat penyemenan, penanganan scale, pasir, korosi dan damage yang mungkin terjadi pada sumuran minyak dan gas bumi.
  • Memahami prinsip-prinsip dasar perancangan : penyemenan, workover, stimulasi sumuran dengan  pengasaman dan perekahan hidrololik, perencanaan work over dan lain-lain

PRE-REQUISITE :

Latar belakang  : Operator, Senior Operator, Engineer/Non Engineer

MATERI TRAINING  :

Geologic Considerations in producing Operation

  • Introduction
  • Sandstone Reservoirs
  • Geologic Factors Affecting Reservoir Properties in Sandstone
  • Application of Geologic concepts in Specific Sandstone
  • Carbonate Reservoirs
  • Application of Geologic Concepts in Carbonate Reservoirs

Reservoir Considerations in Well Completions

  • Introduction
  • Hydrocarbon Properties of Oil and Gas
  • Recommendations of Obtaining Good Test Data
  • “Eyeball” Interpretation of Pressure Charts

Primary Cementing

  • Introduction
  • Cementing Materials
  • Cement Additives
  • Cement Bonding
  • Flow Properties of Primary Cements
  • Displacement Mechanics
  • Cost of Primary Cementing
  • Special Problem Situations-New Developments
  • Primary Cementing Practices

Well Completion Design

  • Factors Influencing Well Completion Design
  • Conventional Tubular Configuration
  • Unconventional Tubular Configurations
  • Sizing Production Tubular
  • Completion Interval
  • Permanent Well Completions (PWC)
  • Tubingless Completion

Tubing Strings,Packers,Subsurface Control Equipment

  • Tubing Strings
  • Steel Grades
  • Tubing Connections
  • Makeup of API Threaded connection
  • Design of Tubing Strings
  • High Strength Tubing
  • Physical Properties of Steel
  • Sensitivities of High Strength Tubing
  • Tubing Inspection
  • Tubing Handling Practices
  • Equipment for Use With-Strength Tubing
  • Tubing Running Practices
  • API Publication List
  • Packers and Subsurface Control Equipment
  • Production Packers
  • Subsurface Control Equipment

Perforating Oil and Gas Wells

  • Introduction
  • Types of Perforators
  • Evaluation of Perforator Performance
  • Factors  Aftecting Gun Perforating Results
  • Perforating in a Clean Fluid with Differential Pressure Into Wellbore
  • A Comparison between the GEO-VANN System and Other Perforating Methods in Wells Equipped with Packers

Completion and Workover Fluids

  • Functions-Requirements-Selection Criteria
  • Formation Damage Related to Solids
  • Oil Fluids-Practical Application
  • Conventional Water-Base Mud
  • Oil Base or Invert-Emulsion Muds
  • Foam
  • Perforating Fluids
  • Packer Fluids
  • Well Killing

Through-Tubing Production Logging

  • Introduction
  • Logging Device
  • Application of Through-Tubing Production logging
  • Field Examples of Production Logging Techniques
  • Primary Cement Evaluation

Problem Well Analysis

  • Problem Wells
  • Problem Well Analysis Checklist

Parafin and Asphaltene

  • Introduction
  • Paraffin and Asphaltene Chemistry
  • Deposition Mechanisms
  • Removal of Wax Deposits
  • Preventing or Decreasing Wax Deposition
  • Design of Wax Control

Squeeze Cementing-Remedial Cementing

  • Introduction
  • Theoretical Considerations
  • Practical Considerations
  • Special Squeeze Cementing Situations
  • Planning a Squeeze Cement Job
  • Normal Operational Procedures
  • Other Operational Procedures
  • Plug-Back Operations
  • Special Cement Systems

Sand Control

  • Introduction
  • Reduction of Drag Force
  • Mechanical Methods of Sand Control
  • Practical Considerations in Gravel Packing
  • Use of screen Without Gravel
  • Resin Consolidation Methods

Formation Damage

  • Introduction
  • Basic Causes of Damage
  • Classification of Damage Mechanisms
  • Reduced Absolute Permeability
  • Increased Fluid Viscosity (Emulsion)
  • Diagnosis of Formation Damage

Surfactants for Well Treatments

  • Characteristics of Surfactants
  • Use and Action of Surfactant
  • Formation Damage Susceptible to Surfactant Treatment
  • Preventing or Removing Damage
  • Well Stimulation With Surfactants
  • Increasing Effectiveness of Rod Pumping
  • Prevention of Well Damage

Acidizing

  • Acids Used in Well Stimulation
  • Acid Additives
  • Carbonate Acidizing
  • Acidizing Techniques for Caronat Formations
  • Sandstone Acidizing
  • Potential Safety Hazard in Acidizing

Hydraulic Fracturing

  • Introduction
  • Mechanics of Fracturing
  • Production Increase from Fracturing
  • Propping the Fracture
  • Frac Fluids
  • Frac Job Design
  • Frac Job Evaluation Techniques

Scale Deposition,Removal,and Prevention

  • Introduction
  • Causes of Scale Deposition
  • Prediction and Identification of Scale
  • Scale Removal
  • Scale Prevention

Corrosion Control

  • The Corrosion Process
  • Detection and Measurement of Corrosion
  •  Corrosion Control

DURASI

3 Hari

FASILITAS

Normal Class

  • Sertifikat, Modul (Soft dan Hard Copy) Flash disc, Training kit (Ballpoint Tas jinjing), Tas Ransel, Jacket, Lunch, 2x Coffe break, foto bersama dan pelatihan dilaksanakan di Hotel berbintang.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Production Operation and Problem Solving 2025:

  • 15-17 Januari 2025 Malang
  • 12-14 Februari 2025 Bogor
  • 12-14 Maret 2025 Surabaya
  • 14-16 Mei 2025 Yogyakarta
  • 11-13 Juni 2025 Jakarta
  • 09-11 Juli 2025 Bali
  • 13-15 Agustus 2025 Bogor
  • 10-12 September 2025 Surabaya
  • 08-10 Oktober 2025 Bandung
  • 12-14 November 2025 Yogyakarta
  • 10-12 Desember 2025 Jakarta

INVESTASI (TIDAK TERMASUK BIAYA AKOMODASI & PENGINAPAN):

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Production Surface Facility Production,Process,Surface Equipment & Its Operation

OBJECTIVES :

After participate in this course, the participants will be able and capable to :

  • Understand the basic concept of oil and gas handling processes and facilities, and how to operate this technology and equipment performance maintenance in field application.
  • Diagnostic of oil and gas reservoir performance under actual drive mechanism and future performance with current handling processes.
  • Analyze the production potential of reservoir under with actual handling system processes and to plan the better development processes according to reservoir capacity.
  • Understand the fundamentals of microscopic and macroscopic aspects and phenomena of oil and gas handling processes.

AUDIENCE:

No specified  (Operator/Sr. Operator/Engineer or Non Engineer)

COURSE OUT-LINE:

Oil Handling and Processing Facilities and Maintenance
Oil Well Surface Production Equipment and Operation

  • Oil Well Equipment
  • Oil Well Production Operation
  • Well Automatic Safety Device

Oil Gathering System. Manifold and Flowline

  • Oil Gathering System
  • Maniflod System
  • Flowline Sizing and Design

Crude Oil and Gas Separation

  • Separator and Principle of Separation
  • Design of Separator
  • Oil Dehydration

Principles of Measurement

  • Introduction to Measurement
  • Crude Oil Measurement
  • Gas Measurement

Well Test

  • Introduction
  • Responsibility for Test
  • Preparation for Test
  • Types of Well Test
  • Equipment and Procedures
  • Accuracy of Fluid Measurement
  • Problem in Testing
  • Type of Test

Gas Handling and Processing Facilities and Maintenance
Introduction to Gas Handling and Facilities
Gas Properties

  • Ideal gas
  • Real Gas
  • Gas Formation Volume Factor
  • Gas Compressibility
  • Gas-Water System
  • Gas-Condensate System

Gas Reservioir Performance

  • Reservoir Gas Flow
  • Gas Reserves
  • Well Completion Effect
  • Tight Gas Well
  • Gas Well Testing

Gas Piping System

  • Basic  Flow Equation
  • Flow in Wells and Flow in Pipelines
  • Effect of Liquids
  • Use of Pressure Traverse Curve
  • Liquid Removal from Gas Wells

Gas Compression

  •  Type of Compressors
  • Compressor Design
  • Centrifugal Compressor

Total System Analysis

  • Tubing and Flow Line Effect
  • Separator Pressure Effect
  • Compressor Selection

Flow Measuring

  • Orifice Metering
  • Metering System Design
  • Other Metering Methods

Gas Condensate Reservoir

  • Well Testing and Sampling
  • Gas Cycling

Field Operation Problems

  • Pressure Cumulative Production Plot
  • Hydrate Formation
  • Sour Gas Production
  • Corrosion Control With Inhibitors
  • Sulfur Deposition

Gas Processing

  • Field treatment of Natural Gas
  • Gas Plant Operation
  • Gas Dehydration
  • Gas Sweetening

DURATION

3 Day

FASILITY

Normal Class

  • Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket or T-shirt, etc, Convenient training facilities in four or five stars hotel, Lunch per day, morning and afternoon coffee / tea breaks for along the training, Certificate & Photo.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training Production Surface Facility Production,Process,Surface Equipment & Its Operation 2025:

  • 20-22 Januari 2025 Jakarta
  • 17-19 Februari 2025 Yogyakarta
  • 17-19 Maret 2025 Bandung
  • 14-16 April 2025 Surabaya
  • 19-21 Mei 2025 Bogor
  • 16-18 Juni 2025 Bali
  • 14-16 Juli 2025 Jakarta
  • 18-20 Agustus 2025 Bandung
  • 15-17 September 2025 Yogyakarta
  • 13-15 Oktober 2025 Bandung
  • 17-19 November 2025 Surabaya
  • 15-17 Desember 2025 Bogor

Investation (Not Include Hotel Acomodation) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Available on request for time, place and facilities call us for more information

REFERENSI :

  1. PT. Conocophillips Indonesia
  2. PT. Armindo Jaya Mandiri

Training Production Surface Facility Production,Process,Surface Equipment & ITS Operation

Training Oil Gas and Water Handling Facilities

Who Should Attend

Production engineers and supervisors, Well Service engineers and supervisors, Materials, logistics and warehouse personnel, Work over engineers and supervisors

You will learn

  • A Comprehensive discussion of Production equipment and practices including Artificial Lift Equipment
  • Understanding the basic of Production Techniques and Production Problems
  • The practical and technical considerations in the design, selection and operation of your down hole and Surface production equipment
  • How to maintain safety environmental excellence in production and well service operations

About The Course

After participate in this training, the participants will be able and capable to :

  • Understand the basic concept of oil , gas and water handling processes and facilities, and how to operate this technology in field application.
  • Diagnostic of oil and gas reservoir performance under actual drive mechanism and future performance with current handling processes.
  • Analyze the production potential of reservoir under with actual handling system processes and to plan the better development processes according to reservoir capacity.
  • Understand the fundamentals of microscopic and macroscopic aspects and phenomena of oil, gas and water handling processes. 

Course Contents

Gas Handling Facilities

Introduction to Gas Handling and Facilities

Gas Properties

  • Ideal gas
  • Real Gas
  • Gas Formation Volume Factor
  • Gas Compressibility
  • Gas-Water System
  • Gas-Condensate System

Gas Reservoir Performance

  • Reservoir Gas Flow
  • Gas Reserves
  • Well Completion Effect
  • Tight Gas Well
  • Gas Well Testing

Gas Piping System

  • Basic  Flow Equation
  • Flow in Wells and Flow in Pipelines
  • Effect of Liquids
  • Use of Pressure Traverse Curve
  • Liquid Removal from Gas Wells

Gas Compression

  • Type of Compressors
  • Compressor Design
  • Centrifugal Compressor

Total System Analysis

  • Tubing and Flow Line Effect
  • Separator Pressure Effect
  • Compressor Selection

Flow Measuring

  • Orifice Metering
  • Metering System Design
  • Other Metering Methods

Gas Condensate Reservoir

  • Well Testing and Sampling
  • Gas Cycling

Field Operation Problems

  • Pressure Cumulative Production Plot
  • Hydrate Formation
  • Sour Gas Production
  • Corrosion Control With Inhibitors
  • Sulfur Deposition

Gas Processing

  • Field treatment of Natural Gas
  • Gas Plant Operation
  • Gas Dehydration
  • Gas Sweetening

Oil Handling Facilities
Oil Well Surface Production Equipment and Operation

  • Oil Well Equipment
  • Oil Well Production Operation
  • Well Automatic Safety Device

Oil Gathering System. Manifold and Flowline

  • Oil Gathering System
  • Manifold System
  • Flow line Sizing and Design

Crude Oil and Gas Separation

  • Separator and Principle of Separation
  • Design of Separator
  • Oil Dehydration

Principles of Measurement

  • Introduction to Measurement
  • Crude Oil Measurement
  • Gas Measurement

Well Test

  • Introduction
  • Responsibility for Test
  • Preparation for Test
  • Types of Well Test
  • Equipment and Procedures
  • Accuracy of Fluid Measurement
  • Problem in Testing
  • Type of Test
  • Water Handling Facilities

The Chemistry of Water

  • Chemical and Physical Properties
  • Water Sampling Procedures
  • Quantitative Analysis of Oilfield Waters
  • Water Analysis Techniques

Water Formed Scales

  • Why Scales Form
  • Predicting Scale Formation
  • Mixing Waters – Compatibility
  • Preventing Scale Formation
  • Scale Removal Methods

Corrosion in Water Injection System and Disposal System

  • Theory of Corrosion
  • The Effect of Metal Composition
  • Effect of Water Composition
  • Forms of Corrosion
  • Corrosion Control Methods
  • Corrosion Inhibitors
  • Internal Coatings and Linings for Tubular Goods
  • Internal Tank Coatings and Cathodic Protection
  • Non-Metallic Tubular Goods Types
  • Removal of Corrosive Gases from Water
  • Oxygen Removal
  • Removal of Hydrogen Sulfide from Water
  • Removal of Carbon Dioxide from Water
  • Oxygen Exclusion
  • Design to Minimize Corrosion
  • Corrosion Monitoring Techniques

DURATION

3 Day

FASILITY

Normal Class

  • Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket or T-shirt, etc, Convenient training facilities in four or five stars hotel, Lunch per day, morning and afternoon coffee / tea breaks for along the training, Certificate & Photo.

Online Class

  • Softcopy Modul dan Sertfikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641, 0821 3874 5980

Email: [email protected]

Website: https://bmdstreet.co.id

Schedule Training Oil Gas and Water Handling Facilities  Tahun 2025 :

  • 22-24 Januari 2025 Bogor
  • 19-21 Februari 2025 Surabaya
  • 19-21 Maret 2025 Bandung
  • 15-17 April 2025 Yogyakarta
  • 21-23 Mei 2025 di Medan
  • 18-20 Juni 2025 Jakarta
  • 16-18 Juli 2025 Bali
  • 20-22 Agustus 2025 Yogyakarta
  • 17-19 September 2025 Bogor
  • 15-17 Oktober 2025 Surabaya
  • 19-21 November 2025 Bandung

Biaya registrasi (tidak termasuk biaya akomodasi & penginapan) :

Online Class

  • Rp 6.100.000/peserta (Harga belum termasuk pajak dan promo)

Normal Class

  • Rp. 12.000.000,-/peserta (Jakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 12.000.000-/peserta (Bandung) (Harga belum termasuk pajak dan promo)
  • Rp. 13.100.000,-/peserta (Yogyakarta) (Harga belum termasuk pajak dan promo)
  • Rp. 15.300.000,-/peserta (Bali) (Harga belum termasuk pajak dan promo)
  • Rp. 16.100.000,-/peserta (Lombok) (Harga belum termasuk pajak dan promo)
  • US$ 4780/peserta (Malaysia) (Harga belum termasuk pajak dan promo)

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Butuh bantuan! Klik disini

Kami siap membantu, silahkan berkomunikasi langsung dengan Tim Kami yang sedang online saat ini. Jika jaringan sedang sibuk, mungkin karena sedang melayani pelanggan lain. Untuk respon cepat silahkan kirim email ke: [email protected] untuk pelayanan via Help Desk

Customer Support

Mei Dwi - Head Office

Online

Customer Support

Umu Hanifatul - Head Office

Online

Customer Support

Eva Arlinda - Head Office

Online

Customer Support

Andini Eryani - Head Office

Online

Mei Dwi - Head OfficeCustomer Support

Hi, Ada yang Bisa saya bantu pak/bu? 00.00

Umu Hanifatul - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00

Eva Arlinda - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00

Andini Eryani - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00