Training production Logging

SUMMARY

Training production Logging – This course is to summarize the state of the art of production logging technology. It included  the example problems to illustrate the use of various theoretical solutions, it also listed an overview of conventional  well log technology and is general introduction to the latest methods of  production logging technology. In the absence of production logs, the performances of  production or injection wells are evaluated on the basis of data obtained from surface measurements, volumes measured in reservoirs, flow rates from separators and pressure measurements at a given down hole point. These data are generally insufficient to determine the flow rate and nature of the fluids produced from or injected into each point in the well. Productions logs provide information required for analyzing the behavior of a well interval. This thus makes it possible to answer four fundamental questions:

  1. What are the producing intervals?
  2. What fluids do they produce?
  3. At what flow rates?
  4. What is the apparent mean permeability of the layers?

By comparison with the true permeability known from cores or log data, the interconnections between each layer and the well are defined. In new wells, an evaluation made with production logs indicates whether  the well is producing as forecast or else whether problems exist  in the completion or in reservoir properties. The periodic use of production log is also a way of checking the state the reserve and of following progress in depletion. In this way, maximum recovery can be obtained. The discovery of problems before the beginning of work over operations enables re-completion procedures to be optimized. Repairs can be simplified and made less dangerous for both the well and the reservoir when the problem has been clearly defined. Production logs are thus a reliable way for solving many production problems. Their main advantage lies in the capacity for determining how and where fluids flow, even outside tubings or casings under production conditions. Production logs are very often used for diagnosing defects altering the proper functioning of well, i.e. tubing leaks, casing leaks, communications due to channeling as result of improper cementing, low-pressure intervals taking up part of the effluent. In this course, it  has also included example problems to illustrate the use of various theoretical solution. Wherever possible, it has not only discussed practical difficulties that one may encounter while using the theoretical solutions, but it has also listed some of the method that one can used to obtain the desired information. It also included descriptions on field histories wherever they were available. This course is mainly directed to the practicing professionals who make engineering calculations and decision on production and injection well  applications. For managers, the book helps to review the present state of the art. It also outlined some of new method in production log technology that exist today, such as radioactivity log. These gaps in technology will be useful for research engineers and research professionals to determine the areas of future research.

OUTLINE

CHAPTER 1

Overview of Conventional Logging

  • Formation Evaluation from Logging Data
  • Rock  Properties From  Logging Data
  • Conventional Log Data Quantification, Determination of  : Lithology, Porosity, Fluid Saturation from Conventional Log Data

CHAPTER 2
Production Logging Technology

  • Definition, History and Recent Technology of Production Logging
  • Well Diagnosis and Reservoir by Production Logging
  • Production Logging for Well Drilling and Completion
  • Production Logging for Production and Injection Well 

CHAPTER 3
Single Phase Fluid Flow in Pipes

  • Laminar and Turbulent Flow
  • Fluid Velocity Profile
  • Annular Flow

CHAPTER 4
Temperature Logging

  • Well Temperature Distribution
  • Temperature Log Data Interpretation
  • Hydraulic Fracturing Evaluation with  Temperature Log

CHAPTER 5
Radioactivity-Tracer Logging

  • Tracer Loss Log
  • Velocity-Shot Log
  • Tracer Placement
  • Radioactive-Tracer Log in Laminar Flow
  • Two Pulse Tracer Logging

CHAPTER 6
Spinner- Flow meter Logging

  • Theory of Spinner Response
  • Log Spinner-Flow meter Log Interpretation
  • Well Flow Measurement by  Spinner Flow meter

CHAPTER 7
Single Phase Flow Profile

  • Back Ground
  • Comparison between  Log Temperature Data, Radioactive Tracer and Spinner Flow meter

CHAPTER 8
Multiphase Flow in Pipes

  • Holdup Definition
  • Flow Pattern
  • Pressure Loss in Pipes
  • Influence of Pipe Slant Angle and Perforation

CHAPTER 9
Production Logging for Multiphase Floe in Pipes

  • Log Data Interpretation
  • Determination Flow Rate
  • Quantitative Analysis of Multiphase Logging Data
  • Qualitative Analysis of Multiphase Logging Data

CHAPTER 10
Noise Logging

  • Theory of  Noise Logging
  • Noise Logging Applications

CHAPTER 11
Cement Quality Logging

  • Cement Bond Log
  • Attenuation-Ratio Log
  • Ultrasonic –Pulse-Echo Log

CHAPTER 12
Case Hole Well Logging

  • Pulse Neutron Log for Determination of Flow Profile
  • Radial Differential Temperature Log
  • Gravel Pack Evaluation
  • Well-Test by Production Logging

DURATION

3 Day

FASILITY

Normal Class

  • Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint, including jacket or T-shirt, etc, Convenient training facilities in four or five stars hotel, Lunch per day, morning and afternoon coffee / tea breaks for along the training, Certificate & Photo.

Online Class

  • Softcopy Modul dan Sertifikat

INFORMATION & PROMO

Call : 021 756 3091

Fax : 021 756 3291

CONTACT PERSON

0813 8280 7230, 0812 8931 1641

Email: [email protected]

Website: https://bmdstreet.co.id

Jadwal Training production Logging 2024:

  • 03-05 Januari 2024 Malang
  • 05-07 Februari 2024 Jakarta
  • 05-07 Maret 2024 Surabaya
  • 02-04 April 2024 Bali
  • 06-08 Mei 2024 Bandung
  • 04-06 Juni 2024 Malang
  • 02-04 Juli 2024 Surabaya
  • 06-08 Agustus 2024 Yogyakarta
  • 03-05 September 2024 Surabaya
  • 02-04 Oktober 2024 Bogor
  • 05-07 November 2024 Bali
  • 03-05 Desember 2024 Surabaya

INVESTASI (TIDAK TERMASUK BIAYA AKOMODASI & PENGINAPAN) :

Online Class

  • Rp 5.500.000/peserta (Online Zoom Meeting)

Normal Class

  • Rp. 11.000.000,-/peserta (Jakarta)
  • Rp. 11.000.000-/peserta (Bandung)
  • Rp. 12.000.000,-/peserta (Yogyakarta)
  • Rp. 14.000.000,-/peserta (Bali)
  • Rp. 14.750.000,-/peserta (Lombok)
  • US$ 4780/peserta (Malaysia)

Available on request for time, place and facilities call us for more information

Butuh bantuan! Klik disini

Kami siap membantu, silahkan berkomunikasi langsung dengan Tim Kami yang sedang online saat ini. Jika jaringan sedang sibuk, mungkin karena sedang melayani pelanggan lain. Untuk respon cepat silahkan kirim email ke: [email protected] untuk pelayanan via Help Desk

Customer Support

Mei Dwi - Head Office

Online

Customer Support

Umu Hanifatul - Head Office

Online

Customer Support

Eva Arlinda - Head Office

Online

Customer Support

Andini Eryani - Head Office

Online

Mei Dwi - Head OfficeCustomer Support

Hi, Ada yang Bisa saya bantu pak/bu? 00.00

Umu Hanifatul - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00

Eva Arlinda - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00

Andini Eryani - Head OfficeCustomer Support

Yth. Bapak/ibu ada yang bisa saya bantu..? 00.00